Shadow 2 Harbinger V2 Slide Milling

(53 reviews) Write a Review
  • Shadow 2 Harbinger V2 Slide Milling
  • Shadow 2 Harbinger V2 Slide Milling
  • Shadow 2 Harbinger V2 Slide Milling
  • Shadow 2 Harbinger V2 Slide Milling
  • Shadow 2 Harbinger V2 Slide Milling
  • Shadow 2 Harbinger V2 Slide Milling
  • Shadow 2 Harbinger V2 Slide Milling
  • Shadow 2 Harbinger V2 Slide Milling
$400.00

Description

Model: CZ Shadow 2

Service: CNC mill your supplied slide for optic, removing rear dovetail & weight reduction (Optic MUST be sent with slide - no exceptions.) ONLY select NO optic cut if you want the rest of the package without the optic cut.

Finish: Cerakote or Black Nitride

 

Our Trijicon RMR, SRO, and Holosun 507 optic cuts utilize our custom made screws. One set is included. Additional sets can be added to order or purchased later here.

 

 

 

View AllClose

53 Reviews

  • 5
    Cz shadow 2 slide machine cut and cerakote

    Posted by Bryan Quisora on Jan 26th 2021

    Realy nice job!!

  • 5
    CZ Shadow 2 slide work.

    Posted by Robyn Gray on Jan 12th 2021

    Quality workmanship. Beautiful.

  • 5
    Harbinger V2 Slide milling

    Posted by Matthew on Dec 20th 2020

    So, I very rarely write reviews, but this one deserves it.

    First of all, I spent about two months peppering Bruce with all sorts of questions as they came to me. Like myself, apparently, Bruce responds to work emails well after hours. I would think of a question at 11PM, and shoot out an email beforeforgot about it. 9 times out of 10, I would hear back within 10 minutes. So customer service is off the charts.

    I had decided to move my Shadow 2 to CO division, and needed to decide where I wanted the optics cut done. After a great deal of research (and as Bruce can attest, lots of late night emails,) I settled on Primary Machine. I am very glad I did.

    I waited for Black Friday, wanting to take advantage of any sales that might crop up at that time. Wait time was advertised as four weeks, which was fine with me as it is the offseason.

    I chose to cerakote the slide in Concrete Grey, because it is a very close grey to the one that Lok uses in their G10 grips. I also chose the front sight blank (because I am anal retentive) as well and the Shadow 2 lettering.

    I placed my order on 11/28, and the slide was received by PM on 12/8 (I waited a few days to ship.) I received an email on 12/14 that my order was shipping. I ordered a couple of other things, so I assumed that it was those smaller items. I contacted PM to be sure, and lo and behold, the slide was on its way! So, a seven day turnaround.

    The work is amazing, and the optic is seated deaper than I would have thought possible. First range trip today, and I could not be happier. Looks great, shoots flat. Doesn't get any better than that!

    So, long story short, Get your slide and cerakote work done by PM, you will be happy that you did!!

  • 5
    Slide

    Posted by Jesse on Dec 20th 2020

    Great work and better customer service

  • 5
    SRO Slide Mill & Cerakote

    Posted by Mike Davis on Oct 14th 2020

    Just got back from the range. Love the new SRO on my Shadow 2. There machine work and Cerakote (Battle worn red) was fantastic. Cannot go wrong with Primary Machine.

  • 5
    Shadow 2 Harbinger V2

    Posted by Kirk Boston on Sep 13th 2020

    Got it back in roughly 4 weeks, looks spectacular. The SRO is milled so deep you can’t even get a business card between it and the top of the slide, you can see light between the optics hood of the SRO and the slide but it is milled to perfection... the slide is light and fast under recoil. The Battle Worn finish is very well done. My Shadow 2 Orange will also be making a trip down there once my eyes can’t handle the iron sights any longer.

  • 5
    bad A$$$

    Posted by Joshua Bauman on Sep 13th 2020

    Alright got the slide and DPP back two days ago, slide to frame fit overly tight which is expected from a battle worn cerakote job. Uses my Drexel felt pads and mothers mag to polish up the rails and joila fits like butter. Took it out and put 200 rounds through it yesterday.OMG whole new feelings. It hardly moves with 135pf loads. My deputies that were with me are very jealous. I shot it alongside my staccato p duo and tit shoots flatter than my 2011. Highly recommend

  • 5
    Awesome Slide Milling

    Posted by Andrew Steed on Aug 11th 2020

    I sent my CZ Shadow 2 slide out to get the V2 slide cut and I added every option I really wanted. I added the front sight blank, engraved CZ Shadow 2 and the black nitride to keep it looking close to factory as I could. It came out amazing and only took about 5 weeks to get it back to me.

  • 5
    Shadow 2 Harbinger V@ + SRO Optic Mill Job

    Posted by Greg Olson on Aug 8th 2020

    This shop is by far the very best in the entire industry for milling work. They actually thought out where the weight of a slide resides and designed a lightning package that spreads the cuts over as much length of the slide as possible fore and aft. Compared to other shops, this is true precision milling. My "Bill Drill" typical ten yard groups are the size of a coin dollar with double drills just as accurate with 0.15-0.16 splits consistently. Don't even think of any other shop for this work. Just Get It Done At Primary Machine

    Greg Olson / USPSA Competitor

View AllClose